PAGE 2A

HOSES - COOLING

THE100 ---- TOP HOSE ---------- VERTICAL FLOW

THE102 ----  “   “  ------ VERTICAL FLOW 1275

THE103 ----  “   “  --------------- CROSSFLOW

THE104 ----  “   “  -------------- EARLY 1500

THE105 ----  “   “  --------------- LATE 1500

BHE100  BOTTOM HOSE   CAST IRON PUMP 948,1098

BHE101    “     “ ALUMINUM PUMP -- “A” SERIES

BHE102    “     “ PUMP TO TUBE CROSSFLOW 1275

BHE103    “     “ RAD. “   “       “      “

BHE104    “     “ ------------- ”1975” - 1500

BHE105    “     “ ----------- ”1976 ON –  “

THIS IS THE LITTLE HOSE THAT YOU SHOULD CARRY IN THE CAR OR IN YOUR SPARES BOX. YOU CAN INSTALL HOSE WITH A SCREW DRIVER RATHER THAN BY REMOVING THE HEAD OR PUMP.

PTH100 – WATER PUMP TO HEAD –----- “A” SERIES

                          
HTH100 HEATER HOSE - VALVE [BACK OF HEAD]TO
HEATER ALSO CALLED THE “?” HOSE -- “A” SERIES

HTH101 ---- THER. TO  RAD. HOSE -76 ON - 1500

HTH102 ---- RAD. TO PUMP HOSE ----- 75 -  “ 

HTH103 ---- RAD, TO PUMP ------- 76 ON -  “

HTH104 ----  L/H TO THER. HOUSING ------  “

HTH105 BLANKING PLATE/HEAT VALVE - “A” SERIES

HTH105 --- HEATER VALVE BASE ----–  “    “  

HTV107 ------ HEATER VALVE -------  “    “

WHC100 --- WIRE HOSE CLAMPS -- 7/16” TO 9/16”

WHC100A --  “    “     “    ---- 3/4” TO 7/8”

WHC100B --  “    “     “    -- 7/9” TO 15/16” 

WHC101 ---  “    “     “    1 3/16” TO 1 3/8”

WHC102 ---  “    “     “    1 1/4” TO 1 7/16”

WHC103 ---  “    “     “    1 3/8” TO 1 9/16”

WHC104 ---  “    “     “    1 7/16” TO 1 5/8”

WHC105 ---  “    “     “    1 1/16” TO 1 7/8”

WATER PUMP FOR THE “A” SERIES MOTOR “NON-APLUS”. THIS PUMP HAS THE DEEP CAST IRON IMPELLER. THIS IS THE BEST UPRATED PUMP FOR YOUR ENGINE.                                                                         

WPL134 ----- WATER PUMP ---------- “A” SERIES

FOR RACING YOU SHOULD USE OUR COMPETITION PUMP THAT HAS THREE IMPELLER BLADES RATHER THAN THE NORMAL 6, BY USING THIS PUMP IT IS LIKE REDUCING THE RPM OF THE PUMP.

WPL134A ---- WATER PUMP ---------- “A” SERIES

WPL101 -----   “    “   ---------------- 1500                                                        

WPD100 - PUMP DRIVE KIT W/GILMER [TOOTH] BELT DRIVE ---------------------------- “A” SERIES

WPD101 ----- PUMP PULLEY ---- ONLY FOR WPD100

WPD102 ----- CRANK PULLEY ---  “    “    “

YOU SHOULD BE USING A LARGE DIA. PULLEY ON THE WATER PUMP IF YOU ARE RACING. THIS GIVES YOU THE SAME WATER FLOW AS IF YOU WERE TURNING THE ENGINE AT A LOWER RPM. THESE PULLIES ARE LISTED BELOW.                                                                              

WPP100 - LARGE DIA. STEEL PULLEY FOR USE WITH WPL134 AND WPL134A PUMPS --------- “A” SERIES

THIS IS THE REAL COOL ALUMINUM PULLEY FOR REDUCING THE WATER PUMP RPM.

WPP100A -------------------------- “A” SERIES

THR101 ---- THERMOSTAT ----- STOCK -------948

THR101A ---     “      160 DEG. -- “A” SERIES

THR101B ---     “      180 DEG. --  “    “ 

THR102 ----     “      192 DEG.---  “    “

THR103 ----- BLANKING SLEEVE -----  “    “ 

THG100 ----- THERMOSTAT GASKET----  “    “ 

THH100 -----     “      HOUSING --------- 948

THH101 -----     “         “    --- 1098,1275

FRP100 ----- FREEZE PLUG -- 4 REQ.-- 948,1098

FRP101 -----    “    “   -- 5 REQ.------ 1275

FRP102 -----    “    “   ------ SET OF 9 1500

FBL100 ----- FAN BELT ------------------- 948

FBL101 -----  “   “   ----- 1098,1275 THRU 67

FBL102 -----  “   “   ----------------- 68-74

FBL103 -----  “   “   ------------------ 1500 

FAP100 -----  “   “   AIR PUMP --------- 1275  

FAP101 -----  “   “    “   “   --------- 1500 

IF YOU ARE RACING AND ELIMINATING THE GENERATOR OR ALTERNATOR WE OFFER A FAN BELT TO GO FROM THE WATER PUMP DIRECTLY TO THE CRANK PULLEY. THIS BELT IS FOR THE 948,1098,1275.                                                                  

CTP100 --------------------------- “A” SERIES

CTP101 ----- LARGE PULLEY BELT ---  “    “      

FBL105 ----- EMERGENCY ROAD USE BELT ---- ALL