3964 ROCKY RIVER DR. CLEVELAND, OHIO 44111 (216) 889-4666
PAGE
23 CAT. TRANS
TRANSMISSION
WE
STOCK MANY BITS FOR THE RIBBED CASE TRANSMISSIONS. THE FOLLOWING
LIST IS A GOOD REPRESENTATIVE LIST. SORRY TO SAY, BUT SOME ITEMS MIGHT BE
OBSOLETE AT THIS TIME.
1. RCT400 ------------------------ LOCK
TAB
2. RCT401 ----1st MOTION SHAFT BALL
BEARING
3. RCT403 ---------- 1ST MOTION
SHAFT-STOCK
3. RCT404 -- 1ST MOTION SHAFT-
STRAIGHT CUT
4. RCT402 - 3RD MOTION SHAFT
BEARING-ROLLER
5. RCT405 ---------------------- BAULK
RING
5. RCT405C --------- COMPETITION
BAULK
6. RCT406 -------- 3RD AND 4TH
SYNCHRONIZER
7. RCT407 - 3RD AND 4TH
SYNCHRONIZER SPRING
8. RCT408 -- 3RD AND 4TH
SYNCHRONIZER BALLS
9. RCT409 ------------------ 3RD
GEAR STOCK
9. RCT410 ----------- 3RD GEAR STRAIGHT
CUT
10. RCT411 ---------3RD GEAR NEEDLE
BEARINGS
11. RCT412 ------------------------ 2ND
GEAR
11. RCT449 ----------- 2ND GEAR
STRAIGHT CUT
18. RCT413 ------------------------ LAYSHAFT
13. RCT414 -------- 1ST GEAR OUTER
RING ONLY
12. RCT410 -------- 2ND GEAR NEEDLE
BEARINGS
17. RCT416 -------------------- REVERSE
GEAR
18. RCT417 --------------- LAYSHAFT
IMPROVED
19. RCT418 ----- LAYGEAR THRUST
WASHER FRONT
20. RCT419 ---------------- LAYGEAR
BEARINGS
21. RCT420 ---------------- LAYGEAR
CIRCLIPS
22. RCT421 ------------------- LAYGEAR
STOCK
22. RCT422 ------------ LAYGEAR
STRAIGHT CUT
23. RCT423 ------------------ DISTANCE
PIECE
LAYGEAR THRUST WASHERS
24. RCT424
REAR .120/.124
24. RCT425
.125/.126
24. RCT426
.127/.128
24.
RCT427
.130/.131
25. RCT428 ------------ FRONT COVER
-- STOCK
IF YOU ARE RACING
THE STRAIGHT CUT GEAR SET IS HIGHLY RECOMMENDED BECAUSE OF THE
RATIOS AND STRENGTH. I HAVE LISTED BELOW THE GEAR RATIOS FOR COMPARISON. THE
STRAIGHT CUT GEAR ARE NOISIER THAN THE HELICAL CUT BUT DO NOT PUT THE SIDE
THRUST ON THE GEAR STACK. IF YOU CANT AFFORD THE WEBSTER BOX THIS IS THE SET
TO USE. THE SET INCLUDES: 1ST MOTION SHAFT, SECOND GEAR, THIRD GEAR, LAYGEAR
AND GASKET SET.
RCT415 -------------- FULL SET --- A SERIES
ONE OF THE MOST
IMPORTANT MODIFICATIONS YOU CAN DO TO A STANDARD OR RACE TRANSMISSION IS TO USE
A front COVER WITH A REAL
SEAL INSTALLED. SEND US YOUR CLEAN USED FRONT COVER AND WE WILL SEND
YOU A COVER WITH THE SEAL INSTALLED. IF YOU ARE USING YOUR TRANSMISSION NOW AND
WANT A FRONT COVER WHEN YOU REBUILD SEE BELOW.
NOTE:
SEE INSIDE BACK COVER FOR EXCHANGE POLICY.
25. RCT429 -- FRONT COVER
-------- WITH SEAL
25. RCT429A - COVER SEAL NEED
OD DIMENSION
26. RCT430
MAINSHAFT[3RD MOTION] BALL BEAR.
27. RCT431 ---------------------- USE RCT400
28. RCT432 ---------------- 1ST AND
2ND FORK
29. RCT433 ---------------- 3RD AND
4TH FORK
30. RCT434 -------------------- REVERSE
FORK
31. RCT435 --------------- FILLER/DRAIN
PLUG
32. RCT436 ------------------ TAILSHAFT
BUSH
33. RCT437 --- REAR OIL SEAL - W/SEAL
& FELT
37. RCT441 - GEAR KNOB TO SPLIT REAR BUMPER
38. RCT442 -
SPILT REAR BUMPER ON
39. RCT443 - SHIFT BOOT ROUND
RUBBER - TO 70
40. RCT444 -
SPLIT BUMPER - 72 ON
40. RCT444A
-------------- 70 ON
41. RCT445 - DUST COVER - TOP OF
BELLHOUSING
42. RCT446 -
RUBBER - LOWER SIDE
43. RCT447 - CLUTCH RELEASE ARM RUBBER BOOT
44. RCT448 ----------------- FULL
GASKET SET
RCT462 --------- FRONT COVER GASKET ONLY
RCT454 -------- O RING FOR SHIFT LEVER
RCT455 ---- 1ST MOTION SHAFT SHIM - .004
RCT456 ----
- .010
RCT457 ----
- .006
RCT458
ANTI-RATTLE SPRING -
SHIFT LEVER
RCT459 ---------- SPRING FOR SHIFT FORKS
RCT460 -------------- SHIFT ROD
3RD/4TH
RCT461 --------------
1ST/2ND
RCT463 -------------- PEG FOR MAIN SHAFT
RCT464
SPEEDO PLASTIC GEAR W/DRIVE TUBE