PAGE 27 CAT. REAR SPRINGS

THE 15 LEAF 1/4 ELLIPTIC SPRINGS ARE NO LONGER AVAILABLE. ONE HAS TO USE THE LATER “HEAVY DUTY”  10 LEAF UNITS, USING THESE SPRINGS, AS THEY ARE ON A BUGEYE, WILL GIVE YOU A VERY HARSH RIDE. YOU CAN MAKE  THE RIDE SOFTER BY REMOVING ABOUT 3 - 4 LEAVES ON THE BUGEYE, ON THE SQUARE BODY CARS, IT WOULD BE BEST TO REMOVE AT LEAST TWO OF THE LEAVES. THESE SPRINGS COME FROM ENGLAND

QES600 ----- PAIR --------------------- 58-63 

THE WINNER’S CIRCLE 1/4 OFFSET SPRINGS ARE THE SPRINGS TO USE IF YOU ARE HAVING PROBLEMS WITH YOUR TIRES RUBBING ON THE INSIDE. THESE SPRINGS HAVE A SOFTER RATE THAN THE ORIGINAL SPRINGS FOR MORE REAR END BITE. THE REAR OF THE CAR WILL BE LOWERED BECAUSE OF LESS SPRING ARCH. THE SPRINGS COME WITH NEW REAR BUSHINGS INSTALLED, NEW CLAMPING BARS, NUTS/BOLTS necessary FOR INSTALLING AND INSTRUCTIONS.

QSB601 --- KIT ----------------- 1/4 ELLIPTIC 

CWP600 - LOWERING WEDGE KIT ----  “     “

QSP602 - STOCK REAR SPRING BUSHING “    “

QSB603 - BOLT FOR REAR OF SPRING - “    “      

QLP600 - TOP LOCATING PLATE ------ “    “      

QUB600 - “U” BOLT W/NUTS – STOCK - “    “       

BRE600 - RUBBER BUMP STOP -------- “    “     

BRP600 - BUMP STOP RETAINING PIN - “    “                

WSA600 - ALUMINUM WHEEL SPACERS - PAIR - 1/4”  

WSA601 -     “      “     “     -  “   - 3/8”    

WSA602 -     “      “     “     -  “   - 3/4”

WSA603 -     “      “     “     -  “   - 1”

WNE800 ----- WHEEL NUT ---------- PRE-ROSTYLE

WNE801 -----   “    “  ----- ROSTYLE – CHROME

WE HANDLE MAG WHEEL LUG NUTS WITH 11/16” DIA. SHANK. THEY CAN BE MACHINED DOWN TO YOUR DESIRED SHAFT SIZE. THESE NUTS COME WITH STEEL WASHERS.

MWN600 ----- 3/8” ------------ THREAD [STOCK]  

MWN601 ----- 7/17” -----------   “   OPTIONAL

WE HANDLE WHEEL STUDS OF DIFFERENT LENGTHS. CHECK OUT THE LENGTHS BELOW. THESE ARE 3/8” DIA.                                                                                                                                                                                                                                         

WCS600 -- 2 1/8” LONG W/ 1 1/8” THREAD LENGTH

wCS601 -- 2 3/8” LONG W/ 3/4”     “      “                

WCS602 -- 2 1/2”  “   W/ 1 1/8”   “      “     

WCS603 -- 3”      “   W/1 1/8”    “      “    

bws600 -- 7/16” dia.  w/3”        “      “          

sws600 – rear stock length wheel studs -- all

WE HANDLE NEW HALF ELLIPTIC SPRINGS OF VARIOUS CONFIGURATIONS. THEY COME FROM ENGLAND AND WILL OUT LAST THE FACTORY UNITS AS FAR AS SAGGING AND BREAKING. SOLD BY THE PAIR.

HES600 ----- STOCK -------------------- 63-74

HES601 -----   “   -------------------- 75-80

HES602 ----- 1” LOWER THAN STOCK ------ 63-74

HES603 ----- 2”   “     “    “   ------  “ “   

YOU CAN PUT THE 1098,1275 SPRINGS ON THE 1500 CARS TO LOWER BY UP TO 3” - 4”. 

THE WINNER’S CIRCLE 1/2 ELLIPTIC OFFSET SPRINGS PROVIDE THE EXTRA TIRE CLEARANCE WHEN WIDE TIRES ARE MOUNTED ON YOUR CAR. THE SPRINGS ARE OF A LOWER SPRING RATE THAN STOCK SPRINGS, WHICH IS NEEDED FOR MORE REAR END GRIP. THE SPRINGS ARE SUPPLIED WITH THE FRONT BUSHINGS INSTALLED. IT IS NECESSARY TO USE RADIUS LINKS WITH THESE SPRINGS. THIS SPRING KIT INCLUDES: SPRINGS AND NYLATRON BUSHING FOR THE REAR SHACKLES,  WHICH THERE ARE 8.

HOS600 --- KIT ----------------- 1/2 ELLIPTIC 

RSB600 --- REAR SPRING BUSHINGS - STOCK 64-80

RSB601 --- FRONT   “      “     -   “    “ “

RSB602 --- REAR    “      “ NYLATRON SET OF 8

NYLATRON IS MOLY FILLED NYLON

SPP600 --- REAR SHACKLE PLATE W/PINS -- 64-80

SLR600 --- SPRING LOCATING RUBBER -----  “ “

SLR601 ---   “       “     POLY -------  “ “

SUB600 --- “U” BOLTS - STOCK LENGTH ---  “ “

XLB600 --- EXTRA LONG “U” BOLTS W/NUTS   “ “

NEW ITEM: -  THE WINNER’S CIRCLE NOW HAS A REAR SPRING SLIDER KIT. THIS KIT ALLOWS THE SPRING TO SLIDE ON THE AXLE HOUSING WHICH ELIMINATES THE SPRING FROM BINDING DURING VERTICAL MOTION. WITH THIS KIT, YOU HAVE TO USE RADIUS LINKS.  THE KIT INCLUDES: XLB600 [EXTRA LONG “U” BOLT KIT], DELRIN SLIDERS, SPACERS AND WASHERS FOR ADJUSTMENT.

SSK600 ----- PAIR -------- FOR OFFSET SPRINGS 

LBA600 ----- LOWERING BLOCKS -- 1/4” --- PAIR

LBA601 -----    “       “    -- 1/2” ---   “

LBA602 -----    “       “    -- 1” -----   “