page 37 CAT. MORE BODY PANELS                                                                         

fbh190 front STEEL bonnet [hood] – “a” series

fbh191   “     “     “      “    ------- 1500 

for a less expensive alternative you can use our fiberglass hood FOR THE SQUARE BODY SPRIDGET. these are quality hoods with provisions for use of stock hinges. less weight, will not rust and look just like the steel unit. the part number can be found in the fiberglass section.

fpa190 front panel – holds grill – “a” series

fpa191   “     “   -   “     “   ------- 1500 

lfv190a ---- lower repair panel -- for fpa190                

lfv190b ----   “     “      “   --  “  fpa191 

SSB190 ----- BONNET BUFFER ---- TO EARLY 1275 

SSB190A ----   “      “    ---------- 1275 ON 

SSB191 ----- SIDE BONNET BUFFER --------- all

BHH190 - HINGE - LARGE ONE PIECE - 62 THRU 68 

BHH191 -   “   - MULTI LEVER TYPE ----- 69 ON 

BRC190 - BONNET CABLE - ROUND KNOB -- THRU 77 

BRC191 -   “      “   - “T” KNOB ------ 78 ON 

BON190 ----- TELESCOPIC HOOD STAY ----- 71 ON 

THERE ARE A WHOLE LOT OF OTHER SMALL PARTS AVAILABLE FOR THE BONNET CABLES AND LATCHES. WE MIGHT HAVE THEM IN USED so give us a call to check what we might have or can get NEW.                                                                                  

“a” post inner panels with 2 hinge screw panels. 

api190 ---------------------- thru 68 ---- rh 

api191 ----------------------  “   “  ---- lh 

api192 ---------------------- 69 on ------ rh  

api193 ---------------------- “  “  ------ lh  

sos190  outer sill - rocker panel thru 74  rh 

sos191    “    “   -   “      “    “   “   lh  

sos190a   “    “   -   “      “   75 on -- rh 

sos191a   “    “   -   “      “   “  “  -- lh  

fec190 - front end cap for rockers – rh - all  

fec191 -  “     “   “   “     “    - lh -  “

rec190 - rear end cap for rockers -- rh -  “

rec191 -  “    “   “   “     “    -- lh -  “ 

the above are a must for a PROFESSIONAL job, for replacing the rockers. these are the best

quality available.

bfb190 ----- fender beading ------ 66” LENGTH  

pft190 closing panel trunk floor to fender rh  

pft191    “      “     “     “    “   “    lh 

tfp190 ----- trunk floor panel -------- 62-80 

tlw190 ----- trunk lid - good used ----  “ “

a fiberglass trunk lid for racing is available. you will find the part number in the fiberglass section

tls190 - trunk lid stay - “automatic” - 71 on  

mts190 ---- rubber trunk seal ---------  “ “  

mbr190 ----   “      “   buffer  rear - 62 on  

mbr191 ----   “      “     “    front -  “ “  

thk190 ---- trunk handle with keys ----  “ “   

clr192 ---- front chassis leg ------------ rh

clr193 ----   “      “     “  ------------ lh  

mff190 ---- front fender - steel thru 69 - rh 

mff191 ----   “     “    -   “    “   “  - lh 

mff192 ----   “     “    -   “   - 70-74 - rh 

mff193 ----   “     “    -   “   -  “  “ - lh  

mff194 ----   “     “    -   “   -- 1500 - rh 

mff195 ----   “     “    -   “   --   “  - lh 

for a less expensive alternative to the above steel fenders, we do sell fiberglass fenders that have flares BUILT IN. if you are restoring a car BACK TO ORIGINAL. these will not do for your project. we might have some used fenders, do give use a call for more info.                

ffr190  lower panel rear of fender thru 74 rh 

ffr191    “     “    “   “    “     “   “  lh 

ffr192    “     “    “   “    “    -- 1500 rh 

ffr193    “     “    “   “    “    --   “  lh

“a” post complete with flange – these are  for the roll up window cars only.                      

apf190a ---------------------------------- rh   

apf191a ---------------------------------- lh   

ops190 ----- lower outer panel 7 1/2” - rh,lh

Sis190 ----- inner rocker panel ---- rh - all  

sis191 -----   “     “      “   ---- lh - all

ods190 -- outer door skin - rh – side curtain  

ods191 --   “     “    “  - lh -  “      “     

low190 --- inner lower door bottom – rh - all 

low191 ---   “     “     “    “    - lh -  “

if you need rear fenders for your 62 thru 80 car, give use a call to find out which fenders are available. of course you can always use our flared rear fenders with the full arch design. part numbers will be found in the fiberglass section.

fls190 lower front of rear fender - 62-80  rh 

fls191   “     “    “   “    “    -  “  “  lh  

flr192   “    rear  “   “    “    -  “  “  rh

flr193   “      “   “   “    “    -  “  “  lh 

iwa190 ---- inner wheel arch - flat top -- rh 

iwa191 ----   “     “    “   -   “   “  -- LH