PAGE 45 CAT. FIBERGLASS                                                                            

FIBERGLASS

FIBERGLASS STOCK FRONT BONNET. THIS FRONT END IS AVAILABLE WITH CAPTIVATED NUTS FOR USE WITH STOCK HINGES. THIS WOULD BE FOR STREET USE. THESE BONNETS ARE OF SUPER QUALITY WHICH WILL NEED MINOR FINISHING BEFORE PAINTING. WHEN INSTALLED ONE CAN NOT TELL IF IT IS STEEL OR FIBERGLASS UNTIL ONE TOUCHES IT. THEY COME WITH THE RADIATOR SHROUDING INSTALLED. WE ALSO SELL ONE THAT IS FOR RACING [OR STREET RACING LOOK] WITHOUT PROVISIONS FOR USING STOCK HINGES. HOOD PINS OR STRAPS CAN BE USED FOR SECURING. BONNETS ARE ALSO AVAILABLE WITH SMALL FLARES  [APPROX. 1 1/2”] AND LARGE FLARE UNIT WHICH ALLOWS FULL TRACK WIDTH ALLOWED IN SCCA RACING. THIS HOOD ALSO INCLUDES ROCKER PANEL SPATS AND AIR DAM. WEIGHT FOR THESE BONNETS BEING ABOUT 45 LBS.. THIS A REAL WEIGHT SAVINGS [LIKE ADDING HORSEPOWER TO YOUR CAR] ON CAR. SHIPPED VIA TRUCK OR CAN BE PICKED UP AT OUR STORE IN CLEVELAND OHIO. IF WE ARE GOING TO A SHOW WE CAN BRING ALONG SO YOU CAN SAVE ON SHIPPING AND BOX FEE. JUST GIVE USE A COUPLE OF WEEKS NOTICE OF YOUR INTENTIONS.

any of the following can be used for street or racing. for vintage racing check with the organization to make sure you can run it.

CFB190C ----- STOCK BONNET ----------- BUGEYE  

CFB190A - SMALL FLARED BONNET - RACE -   “

CFB190B -   “     “      “    - STREET   “      

CFB190D - LARGE   “      “    - RACE -   “       

CFB190E ---- REPLACEMENT AIR DAM -----   “         

RBF190 ----- REAR WHEEL FLARES -------   “        

RBF190A ----  “   racing quarters ----   “      

WE SELL THE ABOVE STREET KIT TO MAKE YOUR MIDGET GIVE THAT “MODERN COKE BOTTLE LOOK”. 

THIS KIT INCLUDES THE FOUR FENDER [COMPLETE], FRONT 1500 BUMPER [FIBERGLASS], MOUNTING BRACKETS, MOUNTING EPOXY FOR REAR FENDERS AND COMPREHENSIVE INSTRUCTIONS. EVERYONE THAT HAS PURCHASED THIS KIT IS WELL PLEASED WITH IT’S QUALITY AND LOOKS. BY THE WAY – FAT TIRES RULE!                                                    

FFK190 ----- STREET KIT --------------- 62 ON     

IF YOU WANT THE SAME FLARED LOOK BUT WITHOUT THE 1500 BUMPER, WE OFFER A KIT WITH JUST THE FOUR FENDERS AT A REDUCED PRICE. THIS KIT CAN BE FOR STREET OR RACING.                                                  

FCS190 ----- FENDERS ONLY KIT --------- 62 ON   

FGF190 - REPLACEMENT FRONT FENDER - RH   “ “  

FGF191 -      “        “     “    - LH   “ “

A FRONT HOOD MADE OF FIBERGLASS IS AVAILABLE WITH ACCEPTABILITY FOR STREET USE OR PLAIN FOR RACING. JUST THINK, NO MORE RUST ALONG THE FRONT EDGE!

FGH190A --- REPLACEMENT HOOD - STREET - 62 ON     

FGH190 ----     “        “   - RACE ---  “ “      

YES, WE DO A TRUNK [DECK] LID. THIS ONLY OFFERED AS A OUTER SKIN. MOUNTING IS WITH PEGS, HOOD PINS, TERRY SPRINGS OR STRAPS.

FGD190 ----- TRUNK LID ---------------- 62 ON  

TO COMPLETE YOUR STREET MACHINE YOU NEED THE FIBERGLASS TONNEAU COVER. THERE IS ON DRAWBACK TO THIS MODIFICATION, THE TOP IS RENDERED UNUSABLE. IF YOU MUST RETAIN THE TOP YOU CAN MODIFY THE PANEL BELOW THE TOP AND BRACKETS.                                                                     

FTC190 ----- TONNEAU COVER ------------ 62 ON        [SIDE CURTAIN CARS ARE EASIER TO MODIFY]