page 46 CAT.
mirrors, grommets
MIRRORS
these
interior mirrors are a very good
reproductions of the original mirrors. it’s hard to tell the difference.
ims120 ----- dash mirror ---------------- 58
thru 66
lim120
----- mirror on center
rod ---------- thru 67
mcr120
----- center rod
--------------------- 67 -69
mrn120 ----- chrome dome nut ------ top of
rod above
mcr121 ----- center rod
---------------------- 70 on
mcn120 ----- nipple ------------- lower of
rod above
lim121 ----- mirror -----------------------
screw on
for
exterior mirrors, we stock various styles. the
lucas reproduction type to the racing “raydot” style.
eml120 ----- lucas type - flat lens ------------ lh
emr120 -----
“ “ - “
“ ------------ rh
eml121 -----
“ “ - convex “
------------ lh
emr121 -----
“ “ -
“ “ ------------ rh
lbp120 ----- lucas backplate only -------- for
above
dmm120 --- door/fender mount with two screws
–- flat
exterior mirrors
were fitted by bmc dealers across the country to fit local laws. if you car does not have an outside mirror it
is wise to fit one. the mirrors do vary in shape ORIGINALLY but the following
are real nice reproduction of the majority installed
mdv120
door mirror RECTANGULAR lh -
stainless flat
mdv121 “ “
“ rh - “
“
mdv122 “
“ “
lh ----– black flat
mdv123 “ “
“ rh ----- “ “
mdv124 “ “
“ ld stainless conv.
mdv125 “ “
“ rh “
“
mdv126 “
“ this is a combination
mirror, the base can be used as a small bolt pattern, 1” apart or
a large bolt pattern of 3.1/2”. this is
the chrome
bullet style
ray120 --------------------------- this is a
perfect copy – less logo – of the original “raydot” mirror. i ran
these mirrors back when? [early 60’s] they were the only real racing mirror
available. they have a spun aluminum body with a flat lens. the base is steel and uses one stud mounting.
if you have a vintage race car this is the mirror to use.
grommets

bugeye
here
are most of the grommets available for the bugeye sprite. if you
have any questions as to which to use, please give us a call and we will look
at our very original car for verification.
mhg001 ----- main harness --------- THROUGH
firewall
gfp001 ----- trans filler ----------------
on tunnel
gfp001 ----- slave cylinder ------ on rh
foot tunnel
dsp001 ----- driveshaft ------------------
on tunnel
scp001 ----- steering column plug - on side
not used
fpp001 ----- sill ----------- on inner
rocker panels
sjp001 ----- jack hole ------- on outer
rocker panel
wds001 --- this grommet will do the following: choke
starter,
heater cable, wiper rack
------ on firewall
ffg001 ---- fuel filler - now you know were
that is!
RCT445 ---- DUST COVER ------- ON TOP
OF BELLHOUSING
RCT446 ---- “ “
------ ON RIGHT SIDE OF TRANS
RCT447
--- CLUTCH RELEASE
ARM ON LEFT “
“ “
62 0N
SOME
OF THE GROMMETS ARE THE SAME AS THE BUGEYE. I WILL LIST THE ONES
THAT ARE ONLY FOR THE 62 AND ON CARS.
SJP001 ----- JACK HOLE
----- 75 ON USE TWO EACH SIDE
LPH001 ----- LICENSE PLATE -----------------
ON REAR
GCT001 ----- WASHER TUBE --------------- ON
FIREWALL
OPT001 ----- OIL PRESSURE TUBE ---------
“ “
LPH001 ----- HEATER CABLE --------------
“ “
OCM001 ----- OIL COOLER --------------- IN
MUDSHIELD
FLW001 ----- FRONT LAMP WIRES ---------
FRONT OF CAR
GHC001 ----- HOOD CABLE ------------- IN
FRONT PANEL
FHC001 -----
“ “ ---------- IN FOOTWELL BOARD
FPP001 ----- FRONT FLOOR -------------------
AT FEET
PTH001 ----- “TOP HAT” PLUG ---- ON SIDE OF
FOOTWELL
FPB001 ----- FUEL PUMP BREATHER
-------------- front
FPB002 ----- “ “
“ -------------- “